One continuous pass from 20 Hz to 20,000 Hz tells you more about a speaker than ten random beeps. This tool sweeps a sine tone across the whole range in 30 seconds, with a live frequency readout, so every weak band announces itself.
A beep tests one frequency at a time and can land in a dead zone by luck. A sweep cannot.
How to Run the Frequency Sweep Test
- Put the device under test near you, at arm’s length.
- Press Start 30 s sweep.
- Watch the big Hz number and the progress bar while the tone rises from 20 Hz to 20 kHz.
- Listen for the spots that get suddenly quiet, harsh, or clicky — and note the Hz number on the display when it happens.
- Press Stop any time. To check a suspicious spot precisely, follow up with the tone generator at that frequency.
The sweep is logarithmic: it spends equal time per octave, so the low end gets the same attention as the top.
Which Band Is Doing What
| Band | Range | What lives there | What a fault sounds like |
|---|---|---|---|
| Sub-bass | 20-60 Hz | Movie booms, sub output | Felt, not heard — hard to fault by ear |
| Low bass | 60-250 Hz | Kick, bass guitar | Dull or missing low end |
| Mids | 250 Hz-2 kHz | Voice, most instruments | Muffled or boxy if weak |
| Presence | 2-5 kHz | Clarity, “s” and “t” edges | Harsh or thin if peaky |
| Treble | 5-20 kHz | Cymbals, air, detail | Fades out early on small speakers |
Small speakers do not fail — they simply stop. A laptop speaker that “loses its top end” near 12 kHz is doing its job, just at the edge of its size limit.
What Is a Frequency Sweep, Exactly?
A sweep is a tone whose frequency rises smoothly over time. This one goes from 20 Hz to 20 kHz in 30 seconds on a logarithmic curve, visiting the entire range in one continuous motion.
Engineers use sweeps because a speaker’s weaknesses are usually narrow: a ported box dips at its tuning frequency, a tweeter crossfade peaks a few dB at one spot. Because the sweep passes every frequency, a narrow fault cannot hide — it shows up as a dip or a crack at a specific Hz, which the live readout writes down for you.
How Do I Test a Tweeter Specifically?
The top of the range is what you want:
- Run the sweep and listen to its final stretch — on a log curve, the last roughly 10 seconds cover the 4 to 20 kHz region.
- A healthy tweeter follows the tone to the very top, quietly.
- If the tone dies around 10 to 14 kHz on a full-range speaker, that is its normal ceiling.
- If it stops at 4 to 6 kHz with a click or crack, the tweeter or its crossover is failing.
- Compare both sides. A tweeter that sounds a half-volume lower than its partner at the same point is the one to replace.
Phone and laptop speakers have no tweeter at all — their “treble” is the same small driver straining, and the top end fading by 12 to 15 kHz is normal.
What Range Do Laptop and Phone Speakers Actually Cover?
Typical real-world numbers (approximate, not spec sheets):
- Phone speaker: about 80 Hz to 15 kHz, with the real music range 100 Hz to 10 kHz.
- Laptop speaker: about 60 to 70 Hz up to 12 to 16 kHz.
- Office 2.0 speakers: 50 to 60 Hz floor, 15 to 18 kHz top.
- Car head unit with stock doors: 45 to 50 Hz floor (the sub does the rest), 16 to 18 kHz top.
If your sweep matches these floors, the hardware is fine. If it cuts off 20 to 30 Hz higher than the table, something is wrong — a clogged port, a blown driver, or a dead amplifier channel.
Frequency Sweep Test in Pakistan and the UAE
In Pakistan, it is the shop-floor tool: one slow pass from the phone shows whether the low end is a blown woofer or a clogged bass port before anyone quotes a replacement. In the UAE, it appears in home-cinema commissioning (confirming the crossover handover between speakers and sub) and in pre-event AV checks, where a sweep in the hall finds the dead zone a playlist never would.
Either way, the rule is the same: test the range, not the volume.
Related Audio Tools
- Tone generator — freeze on one exact frequency
- Sub bass test — fixed 20-60 Hz steps for the low end
- Noise generator — a flat noisefloor instead of a moving tone
- All audio tools in one place
Frequently asked questions
The sweep sounds like a rising siren. Is that right?
Yes. On a logarithmic curve it accelerates in Hz terms, which is why it sounds like a siren reaching pitch.
Why does the sweep feel louder in the middle?
Low frequencies need more energy to sound equally loud, so a constant-amplitude sweep naturally feels soft at the ends and loud in the mids. This tool keeps the amplitude flat and honest rather than applying a loudness curve.
Can I use it to test headphones?
Yes. A good pair follows the sweep to 18 kHz or higher. A drop before 15 kHz means the driver is limited or the pad seal is broken.
My car doors sound boomy at the start of the sweep. Bad?
Boomy 20 to 80 Hz in a car is usually door fitment and carpet, not the amp. Tighten the fitment and re-run.
How long is the sweep?
30 seconds, one logarithmic pass from 20 Hz to 20 kHz. There is no separate slow mode — the log curve already spends equal time per octave.
Last updated: 31 October 2026.