A speaker can play the same song, at the same volume, and still be wired backwards. This tool finds that: whether the left and right drivers move in sync, or against each other.
It plays a 100 Hz sine into both channels and, in the “reversed” mode, flips one side. Wrong wiring becomes audible by ear in about four seconds.
How to Run the Speaker Polarity Test
- Connect both speakers the way you normally do.
- Press In phase (normal) — the tone should feel full and grounded.
- Press Out of phase (reversed) — the same tone should drop in bass and sound thinner.
- Use Compare (auto A/B) to alternate the two, then swap one speaker’s wires and repeat. If the impression of “which one is deeper” flips, that speaker was wired backwards.
The comparison runs four alternations, so you are never comparing two memories.
What You Should Hear in Each Mode
| Button | What you should hear |
|---|---|
| In phase (normal) | A full, tight 100 Hz tone, grounded in the bass |
| Out of phase (reversed) | The same tone thinner and hollow, with the low end pulled out |
| Compare (auto A/B) | A/B alternates four times; the deeper, tighter one is the correct wiring |
The physics: when both drivers push air in the same direction, the low waves add up. When one pushes in and the other out, they cancel — mostly in the bass, where the waves are long. With two identical speakers, that cancellation is exactly what makes the music sound “flat” for no obvious reason.
Common Mistakes When Testing Polarity
- Testing with a mono source. A phone playing a single-channel file can hide the problem. This tool sends true stereo — use it, not your playlist.
- Swapping the wrong wires. Swap both terminals on one speaker at once. Swapping only the positive terminal is the correct swap; swapping both moves nothing.
- Blaming the amplifier. If both speakers are out of phase with each other, one of them is reversed, not the amp. An amp that flips both channels still plays in phase with itself.
- Listening at too low volume. The cancellation is clearest at normal room volume, close to the speakers.
Why Does My Bass Sound Weak Even at High Volume?
If the low end is thin no matter how loud you turn it, polarity is a top suspect. Two speakers fighting each other cancel exactly the frequencies a small driver already struggles with.
Check order:
- Run the Compare (auto A/B) button at normal volume. If “B” (out of phase) sounds better than “A”, a speaker is reversed.
- Re-run after swapping the wires on one speaker.
- If both still cancel, the problem may be placement: speakers pushed far apart from the listening position start fighting in the low end on their own.
After the fix, the sub bass test shows the difference — 60 Hz goes from a vague thump to a tone you can hum along with.
How Do I Tell If My Subwoofer Is Out of Phase?
Be honest about what this tool does: its 100 Hz tone mostly drives the mains speakers, because most sub crossovers sit around 80 Hz. So use a two-step approach:
- Play a bass-heavy track (or the sub bass test at 60 Hz and 40 Hz) with the sub’s polarity switch in one position.
- Flip the switch and listen again at the same volume.
There is no universal “correct” position — room acoustics decide. The ear decides: pick the setting where the bass hits harder without getting boomy.
Speaker Polarity Test in Pakistan and the UAE
Home-cinema installs in the UAE run this after every cable run — a single reversed wire in a 5.1 setup ruins the low end, and re-testing five cables by ear is slow. In Pakistan, audio shops use it when a customer says “the bass was fine yesterday”, because half the time the wire was tugged loose and re-seated backwards.
It also saves a real cost: a driver that is not broken, just reversed, should never be quoted for replacement.
Related Audio Tools
- Speaker LR test — find a dead or weak channel
- Sub bass test — hear the result of a polarity fix
- Water out of speaker — muffled bass can be water, not phase
- All audio tools in one place
Frequently asked questions
Does out-of-phase wiring damage speakers?
No. It wastes energy and cancels bass, but it does not burn drivers. Fix it for sound quality, not safety.
I have two identical speakers. Can I skip the test?
No — that is exactly when it matters most. Identical speakers wired opposite each other cancel the most.
The in-phase and out-of-phase buttons sound the same to me.
Move closer, raise the volume to a normal listening level, and use the Compare (auto A/B) button. Small speakers barely reproduce the cancelling range.
One speaker sounds thin but the test says both are in phase.
Then it is a driver or crossover issue, not wiring. The speaker LR test isolates which channel is weak.
Does it work with a single laptop speaker?
Polarity needs two drivers to compare. A single speaker cannot be “out of phase” with itself — use the tone generator to check its range instead.
Last updated: 31 October 2026.